Snowplow Forums banner
Cancel

Gallery

Navigation

Browse albums
7 This is the 1X2 welded into place. You can also see the square tube cut through the side. I also took a piece of stainless steel pipe and cut them

7 This is the 1X2 welded into place. You can also see the square tube cut through the side. I also took a piece of stainless steel pipe and cut them

  • 0
  • 0
6 I cut through the X bracing and through a little of the bracing for the trip edge in order to run a larger piece of square tube across the back of t

6 I cut through the X bracing and through a little of the bracing for the trip edge in order to run a larger piece of square tube across the back of t

  • 0
  • 0
5 I ground (36 grit sanding wheel) all the Meyer yellow off that I could. This was in preparation for the POR-15 paint which needs to bond with bare

5 I ground (36 grit sanding wheel) all the Meyer yellow off that I could. This was in preparation for the POR-15 paint which needs to bond with bare

  • 0
  • 0
4 After moving the tab for the marker to the inside of the L bracket, I ground all the factory powder coating off then shot the L with weld through pr

4 After moving the tab for the marker to the inside of the L bracket, I ground all the factory powder coating off then shot the L with weld through pr

  • 0
  • 0
3 Next, I made a slice up the center of each bump and up through the bend then hammered them flat. Next all cuts got welded tight. I also welded caps

3 Next, I made a slice up the center of each bump and up through the bend then hammered them flat. Next all cuts got welded tight. I also welded caps

  • 0
  • 0
2 Solution was to take a piece of 1X2 steel and bend it to match the curve of the plow. This left bumps at each bend.

2 Solution was to take a piece of 1X2 steel and bend it to match the curve of the plow. This left bumps at each bend.

  • 0
  • 0
1 This shows why I had to do so much fabrication. 1) The portion of the L bracket that is perpendicular to the moldboard is over an inch in from the

1 This shows why I had to do so much fabrication. 1) The portion of the L bracket that is perpendicular to the moldboard is over an inch in from the

  • 0
  • 0
BOBCAT RESIZED

BOBCAT RESIZED

  • 0
  • 0
Yard Signs resized

Yard Signs resized

  • 0
  • 0
S 990 09.08.2011 024

S 990 09.08.2011 024

  • 0
  • 0
S 990 09.08.2011 023

S 990 09.08.2011 023

  • 0
  • 0
S 990 09.08.2011 022

S 990 09.08.2011 022

  • 0
  • 0
S 990 09.08.2011 011

S 990 09.08.2011 011

  • 0
  • 0
S 990 09.08.2011 010

S 990 09.08.2011 010

  • 0
  • 0
S 990 09.08.2011 009

S 990 09.08.2011 009

  • 0
  • 0
S 990 09.08.2011 008

S 990 09.08.2011 008

  • 0
  • 0
S 990 09.08.2011 005

S 990 09.08.2011 005

  • 0
  • 0
S 990 09.08.2011 003

S 990 09.08.2011 003

  • 0
  • 0
99 Dodge Ram 3500 004L

99 Dodge Ram 3500 004L

  • 0
  • 0
77 Pete wish I never sold

77 Pete wish I never sold

  • 0
  • 0
old pic's 217

old pic's 217

  • 0
  • 0
77 K30

77 K30

  • 0
  • 0
old pic's 019

old pic's 019

  • 0
  • 0
Dad's shop 50's

Dad's shop 50's

  • 0
  • 0
20c5e heavydutyflyer2

20c5e heavydutyflyer2

  • 0
  • 0
Top